DennysDriveshaft.com
Free Shipping on Orders Over $99.00

Product Search
Denny's Driveshaft builds custom steel and aluminum driveshafts for your high performance car, street rod, race car, van, pick up or 4x4 truck
 
Dana Spicer 3-2-809 Flange Yoke 2.75 diameter male pilot 1350 series fits 1963 to 1979 CORVETTE Rear Axle half shafts with OUTSIDE snap rings
Part #:
3-2-809
Your Cost $45.95

Dana Spicer 3-2-809

Flange Yoke fits CORVETTE Rear Axle 1963-1979

1350 Series

  • A - Flange or Swing Diameter = 4.500 inches
  • B - Bolt Circle Diameter = 3.750 inches
    • Bolt Hole Diameter = 0.438 inches
    • Bolt Holes = 4
    • Bolt Holes = DRILLED
  • C - Center Pilot Hole Diameter = 2.750 inches
    • Center Pilot = MALE
  • Series = 1350
    • Outside Snap Ring Style
    • U-Joint Width between snap rings = 3.625 inches
    • D - U-Joint Bearing cap diameter = 1.187 inches
  • G - Center of u-joint bore to Face of flange = 1.281 inches
  • X - inches
  • Y - inches
  • Special Notes: CORVETTE REAR HALF SHAFT FLANGE YOKE

 


Spicer
Dana Spicer 3-2-809 Flange Yoke 2.75 diameter male pilot 1350 series fits 1963 to 1979 CORVETTE Rear Axle half shafts with OUTSIDE snap rings
Dana Spicer 3-2-809 Flange Yoke 2.75 diameter male pilot 1350 series fits 1963 to 1979 CORVETTE Rear Axle half shafts with OUTSIDE snap rings
FOR FASTER SERVICE, PLEASE ORDER ALL PARTS ONLINE
STATUS:  IN STOCK
YOUR COST:  $45.95

Dana Spicer 3-2-809

Flange Yoke fits CORVETTE Rear Axle 1963-1979

1350 Series

  • A - Flange or Swing Diameter = 4.500 inches
  • B - Bolt Circle Diameter = 3.750 inches
    • Bolt Hole Diameter = 0.438 inches
    • Bolt Holes = 4
    • Bolt Holes = DRILLED
  • C - Center Pilot Hole Diameter = 2.750 inches
    • Center Pilot = MALE
  • Series = 1350
    • Outside Snap Ring Style
    • U-Joint Width between snap rings = 3.625 inches
    • D - U-Joint Bearing cap diameter = 1.187 inches
  • G - Center of u-joint bore to Face of flange = 1.281 inches
  • X - inches
  • Y - inches
  • Special Notes: CORVETTE REAR HALF SHAFT FLANGE YOKE

 

Installation Tip:

When changing a flange yoke on any 1963-1979 Corvette half shaft you should be carefull to never strike the flange yoke or driveshaft with a hammer. The u-joint must be pressed into place and care must be given not to ever squeeze the driveshaft tubing in a vise. This will cause permanent damage! Also a Corvette flange yoke can be bent if not supported properly while pressing the u-joint into place. The best way to achieve this is to bolt the flat flange surface to a heavy piece of steel plate so it cannot bend while you are working on it.

image/jpeg

Dana Spicer 3-2-809 Flange Yoke 2.75 diameter male pilot 1350 series fits 1963 to 1979 CORVETTE Rear Axle half shafts with OUTSIDE snap rings

Dana Spicer 3-2-809 Flange Yoke 2.75 diameter male pilot 1350 series fits 1963 to 1979 CORVETTE Rear Axle half shafts with OUTSIDE snap rings

Click to Load this Photo
Click Here to Enlarge
Click to Load this Photo
Click Here to Enlarge

You May Also Need These Parts to Complete the Job

Enter your email address and we'll send you a message when this item is available

Please enter your email address in order to be notified when this item is available.
DennysDriveshaft.com - © Copyright 2020-Present

Website and Web Hosting by Online Media
Online Media - Buffalo's Web Hosting Company