Yukon YP SP706570 replacement for Dana Spicer 706570X SPINDLE with bearing and seals fits 1985 to 1993-1/2 DODGE D500, D600, D800 with DANA 44 Disconnect front axle - FREE SHIPPING

Part Number:
YP SP706570

UPC:

883584323419

Your Cost $187.95

STATUS: IN STOCK - FREE SHIPPING

Yukon YP SP706570 replacement for Dana Spicer 706570X

SPINDLE with bearing and seal kit
- Comes with 706527X spindle bearing and seal kit
- Comes with inner spindle bearing installed at the proper depth.
Fits DODGE D500, D600, D800 with Dana 44 Disconnect front axle
- 1985, 1986, 1987, 1988, 1989, 1990, 1991, 1992, 1993, 1993-1/2
NOTE: For 1985, 1986, 1987
- This spindle will also fit LEFT side but you must remove the internal needle bearing that is not needed on 1985 to 1987 axles with left side bearing and seal at outer end of left side axle tube.
6 Bolt Holes

Yukon YP SP706570 replacement for Dana Spicer 706570X SPINDLE with bearing and seals fits 1985 to 1993-1/2 DODGE D500, D600, D800 with DANA 44 Disconnect front axle - FREE SHIPPING

Click for Larger Photo

FOR FASTER SERVICE, PLEASE ORDER ALL PARTS ONLINE

STATUS: IN STOCK - FREE SHIPPING

YOUR COST: $187.95

This item qualifies for FREE GROUND SHIPPING to the lower 48 states

FREE GROUND Shipping**

**Free Ground Shipping to lower 48 States ONLY...Alaska and Hawaii at reduced rates.

Yukon YP SP706570 replacement for Dana Spicer 706570X

SPINDLE with bearing and seal kit
- Comes with 706527X spindle bearing and seal kit
- Comes with inner spindle bearing installed at the proper depth.
Fits DODGE D500, D600, D800 with Dana 44 Disconnect front axle
- 1985, 1986, 1987, 1988, 1989, 1990, 1991, 1992, 1993, 1993-1/2
NOTE: For 1985, 1986, 1987
- This spindle will also fit LEFT side but you must remove the internal needle bearing that is not needed on 1985 to 1987 axles with left side bearing and seal at outer end of left side axle tube.
6 Bolt Holes

DIMENSIONS

A = 1-5/8 in. OD for Outer Wheel Bearing
B = 2 in. OD for Inner Wheel Bearing
C = 2-1/2 in. OD for Seal
D = 3-3/8 in.
E = 7/16 in.
F = 3/8 in.
G = 5-5/8 in.
H = 6-7/16 in.
K = 4-3/4 in.
Bolt Holes = 6
Bolt Hole Diameter = .390 in.

Also known as part #: YPSP706570

How to Measure a 4X4 Front Axle Spindle at Denny's Driveshafts

Yukon YP SP706570 replacement for Dana Spicer 706570X SPINDLE with bearing and seals fits 1985 to 1993-1/2 DODGE D500, D600, D800 with DANA 44 Disconnect front axle - FREE SHIPPING

You May Also Need These Parts to Complete the Job

DANA SPICER 31139 Outer Spindle Nut for DANA 44 and DANA 44IFS FRONT Part#: 31139 $6.34	DANA SPICER 21588X Inner Spindle Nut WITH PIN for DANA 44 and DANA 44IFS FRONT Part#: 21588X $11.60
DANA SPICER 28068X Spindle Nut Set for DANA 30, 44 and GM 8.5 inch FRONT 1.625-16 thread size Part#: 28068X $14.70	DANA SPICER 36569 - Spindle Washer Locking Ring with holes for Manual Locking Hubs Part#: 36569 $2.54
DANA SPICER 39909 Spindle Washer Locking Ring with holes for Auto Locking Hubs Part#: 39909 ~~$32.10~~ $26.88

Enter your email address and we'll send you a message when this item is available

Please enter your email address in order to be notified when this item is available.

[ X ]

Driveshaft and Driveline Parts > SPINDLES > DODGE > with DANA 44 Front Axle

You May Also Need These Parts to Complete the Job

Enter your email address and we'll send you a message when this item is available