DennysDriveshaft.com
Free Shipping on Orders Over $99.00

Product Search
Denny's Driveshaft builds custom steel and aluminum driveshafts for your high performance car, street rod, race car, van, pick up or 4x4 truck
 

Cobra Kit Car Driveshafts

Cobra Kit Car Driveshafts
Cobra Kit Car Driveshafts at Denny's Driveshafts

Denny's Custom Made Driveshafts

Built specifically for COBRA KIT Cars


 

Custom built to fit your application in 1310, 1330 or 1350 Series.    

 
 
  • Cobra Kit Car Driveshaft pricing for driveshafts up to 20 inch center to center. 
  • Scroll down for popular shaft combinations.
  • If your application is not listed below please call with dimensions for exact quote.
  • Pricing will include Transmission Slip Yoke and Spicer Universal Joints
  • Additional cost for flange yoke if required

 

Rear End PINION YOKEPlease see our Diagram "B" to measure correctly for vehicles with rear differentials using a PINION YOKE

 

FLANGE YOKEPlease see our Diagram "K" to measure correctly for vehicles with rear differentials using a FLAT FLANGE YOKE

You will also need the bolt circle, bolt pattern and pilot dimensions for  Diagram "L" to place your order

 


Whether you are using GM or Ford engines, transmissions or rear ends or any combination of them ...we can make the connection with one of our Cobra Kit Car Driveshafts.

Our 3 inch Cobra Kit Car driveshaft is the most popular choice. Comes in 1310, 1330 and 1350 series. It will handle the horsepower and deliver smooth performance throughout your entire rpm range.

You can also have one built using 2 inch or 2.5 inch tubing if space or clearance is an issue.

Each shaft comes fully assembled with a new transmission slip yoke, Spicer solid body universal joints and, if required, a new flange yoke.. We use the solid body type of universal joint instead of the weaker greaseable type because we know you really do not want all that messy grease splattered all over that beautiful frame work.
  
We build them with meticulous attention to detail. Each shaft is HIGH SPEED - HIGH RPM BALANCED and TESTED on special equipment to be sure it will run the rpm that you require. If it does not pass this test it doesn't get shipped out. No guess work here...we know what it will do for you because of this final test. That is why a DENNY'S DRIVESHAFT will perform BEST in your application.

At the rear end...whether you have a Ford 9 inch, Ford 8.8 (up to 2004) or Jag Independent rear we have you covered. If you have a different model rear end please call or email and let us know what you have so we can discuss your application.

***If you have the flat flange style rear typically found on Ford 8.8 (up to 2004) and Jaguar differentials then please use Diagram "K" and also Diagram "L" to determine the correct bolt circle, bolt pattern and pilot dimensions to place your order.

***If you have a normal pinion yoke style rear end on a Ford 9 inch, Ford 8.8 or Jag rear end then please use Diagram "B" to place your order.  

We also have a variety of replacement U-BOLT STYLE PINION YOKES for both types.

As with all our Cobra Kit Car Driveshafts "IF YOU EVER TWIST OUR STEEL TUBING OR BREAK OUR WELDS... We'll Replace it FREE!" Confidence you can rely on.


 It's Easy to ORDER one NOW!

TO ORDER:   Please measure using ONE of the following Measuring Diagrams.

AFTER you have measured:

ORDER ANYTIME ONLINE by CLICKING on the choices below
After you place your order online you will receive an email to send us the dimensions

If you would rather do it by phone please call us at 1-800-955-1872

 

FREE SHIPPING for Cobra Kit Car Driveshafts


Cobra Kit Car Driveshafts

1310 series

2 inch Tube

2.5 inch Tube

3 inch Tube

UPGRADE - SLIP YOKE

1330 Series

2.5 inch Tube

3 inch Tube

UPGRADE - SLIP YOKE

1350 Series

3 inch Tube

UPGRADE - SLIP YOKE


 

Denny's can custom build a Cobra Kit Car Driveshaft to fit your exact application.

DennysDriveshaft.com - © Copyright 2024-Present

Website and Web Hosting by Online Media
Online Media - Buffalo's Web Hosting Company