DennysDriveshaft.com
Free Shipping on Orders Over $99.00

Product Search
Denny's Driveshaft builds custom steel and aluminum driveshafts for your high performance car, street rod, race car, van, pick up or 4x4 truck
 
2060108-CM SONNAX Forged Chromoly 1350 series 32 splines fits T-400, 4L80, 4L85, 6L80 Light TRUCK Transmissions that originallly had a bolt on yoke at rear output - FREE SHIPPING
Part #:
2060108-CM
Your Cost $145.95

2060108-CM

SONNAX Forged Chromoly Transmission Slip yoke

  • 1350 Series 
  • 32 spline
  • Fits light truck style T-400, 4L80, 4L85, 6L80

DOES NOT FIT.... T400/475 with the emergency brake and or roller bearing in the tailshaft housing as found in the RV Motor Home Transmission and Medium Truck Transmissions
>>>> Please consult a transmission rebuilder to see what is required to convert it to a normal light truck tailshaft and tailshaft housing.

  • Specifically made for Denny's Driveshafts by SONNAX
  • Specifically designed to replace the factory bolt on yoke for T-400, 4L80, 4L85, 6L80 Light Truck Transmissions with the Threaded Hole in the center of the Output shaft.
  • Replaces the light truck style bolt on yoke with a normal car style slip yoke which will allow for proper slip travel and bushing contact for best performance. A must have when using any T-400, 4L80, 4L85 or 6L80 truck transmission with the threaded hole in the output shaft.

With this counterbored slip yoke you can now use a normal car style driveshaft.

This slip yoke will slide all the way into the transmission. 

  • We strongly suggest that you remove the O-Ring on the output shaft because with this slip yoke it is no longer necessary. 
  • Removing the O-Ring will to allow the lubrication to get to the splines...and this is very important.

To determine correct driveshaft center to center length for this slip yoke

  • Push the slip yoke all the way into transmission and pull it out 3/4 inch minimum to 1 inch maximum. Now measure from center of u-joint hole in slip yoke to the center of the u-joint at the rear end yoke.  This dimension will be the correct center to center required for your driveshaft to fit correctly using this slip yoke.

We designed this yoke to solve this problem over 30 years ago when T400 Truck Transmissions first started to be used in cars

  • Barrel Diameter = 1.886 inches
  • Fits U-joint cap diameter = 1.187 inches
  • Fits U-joint width = 3.625 inches
  • Outside Snap Ring style
  • Series = 1350
  • Spline count = 32
  • Counterbored

SONNAX
2060108-CM SONNAX Forged Chromoly 1350 series 32 splines fits T-400, 4L80, 4L85, 6L80 Light TRUCK Transmissions that originallly had a bolt on yoke at rear output - FREE SHIPPING
2060108-CM SONNAX Forged Chromoly 1350 series 32 splines fits T-400, 4L80, 4L85, 6L80 Light TRUCK Transmissions that originallly had a bolt on yoke at rear output - FREE SHIPPING
FOR FASTER SERVICE, PLEASE ORDER ALL PARTS ONLINE
STATUS:  IN STOCK - FREE SHIPPING
YOUR COST:  $145.95
This item qualifies for FREE GROUND SHIPPING to the lower 48 states

FREE GROUND Shipping**

**Free Ground Shipping to lower 48 States ONLY...Alaska and Hawaii at reduced rates.

2060108-CM

SONNAX Forged Chromoly Transmission Slip yoke

  • 1350 Series 
  • 32 spline
  • Fits light truck style T-400, 4L80, 4L85, 6L80

DOES NOT FIT.... T400/475 with the emergency brake and or roller bearing in the tailshaft housing as found in the RV Motor Home Transmission and Medium Truck Transmissions
>>>> Please consult a transmission rebuilder to see what is required to convert it to a normal light truck tailshaft and tailshaft housing.

  • Specifically made for Denny's Driveshafts by SONNAX
  • Specifically designed to replace the factory bolt on yoke for T-400, 4L80, 4L85, 6L80 Light Truck Transmissions with the Threaded Hole in the center of the Output shaft.
  • Replaces the light truck style bolt on yoke with a normal car style slip yoke which will allow for proper slip travel and bushing contact for best performance. A must have when using any T-400, 4L80, 4L85 or 6L80 truck transmission with the threaded hole in the output shaft.

With this counterbored slip yoke you can now use a normal car style driveshaft.

This slip yoke will slide all the way into the transmission. 

  • We strongly suggest that you remove the O-Ring on the output shaft because with this slip yoke it is no longer necessary. 
  • Removing the O-Ring will to allow the lubrication to get to the splines...and this is very important.

To determine correct driveshaft center to center length for this slip yoke

  • Push the slip yoke all the way into transmission and pull it out 3/4 inch minimum to 1 inch maximum. Now measure from center of u-joint hole in slip yoke to the center of the u-joint at the rear end yoke.  This dimension will be the correct center to center required for your driveshaft to fit correctly using this slip yoke.

We designed this yoke to solve this problem over 30 years ago when T400 Truck Transmissions first started to be used in cars

  • Barrel Diameter = 1.886 inches
  • Fits U-joint cap diameter = 1.187 inches
  • Fits U-joint width = 3.625 inches
  • Outside Snap Ring style
  • Series = 1350
  • Spline count = 32
  • Counterbored

 

Denny's Counterbore Drawing

2060108-CM SONNAX Forged Chromoly 1350 series 32 splines fits T-400, 4L80, 4L85, 6L80 Light TRUCK Transmissions that originallly had a bolt on yoke at rear output - FREE SHIPPING

2060108-CM SONNAX Forged Chromoly 1350 series 32 splines fits T-400, 4L80, 4L85, 6L80 Light TRUCK Transmissions that originallly had a bolt on yoke at rear output - FREE SHIPPING

Enter your email address and we'll send you a message when this item is available

Please enter your email address in order to be notified when this item is available.
DennysDriveshaft.com - © Copyright 2019-Present

Website and Web Hosting by Online Media
Online Media - Buffalo's Web Hosting Company