DennysDriveshaft.com
Free Shipping on Orders Over $99.00

Product Search
Denny's Driveshaft builds custom steel and aluminum driveshafts for your high performance car, street rod, race car, van, pick up or 4x4 truck
 
9877740 Pinion Yoke 1350 Series Forged U-Bolt style fits 1985 to 1992 FORD F250, F350 Super Duty 10.25 inch Sterling rear ends
Part #:
9877740
Your Cost $125.95

9877740

  • Pinion Yoke for FORD Super Duty Rear End
    • Fits Ford F250, F350 Super Duty Truck with 10.25 inch FORD Sterling Rear
      • 1985, 1986, 1987, 1988, 1989, 1990, 1991, 1992
  • 31 Splines 1.343 spline diameter
  • U- Bolt style
  • FORGED Steel for extra strength
  • Comes with pinion nut and u-bolt set
  • 1350 Series - fits 1350 series universal joint 5-178X or 5-1350X ... see bottom of this page
    • E = Fits Universal joint 3.625 inches (3-5/8) wide cap to cap
    • D = Fits u-joint bearing cap diameter 1.187 inch (1-3/16)
    • Q = 1.265 inches through splined hole
    • S = 3.150 inches tall
    • R = 1.812 inches seal surface diameter
THIS Yoke is 3-1/8 inches TALL
IMPORTANT:   Late 1993, 1994, 1995, 1996, 1997, 1998 Ford 10.25 inch Sterling rear end pinion yokes could be 3.5 inches (3-1/2) tall.  Please check yours to be sure before ordering.
  • CLICK HERE if you need the 3-1/2 inch tall yoke part number 9870041 for 10.25 inch from 1993 to 1998

NOTES:

  • DOES NOT fit Ford Super duty with DANA rear end
  • NOT compatible with 1330 series driveshaft. 
    • Requires 1330 to 1350 combination u-joint to make connection. CLICK HERE
  • NOT compatible with 1410 series driveshaft
    • CLICK HERE for 1410 series Ford Sterling pinion yokes

 

9877740 Pinion Yoke 1350 Series Forged U-Bolt style fits 1985 to 1992 FORD F250, F350 Super Duty 10.25 inch Sterling rear ends
9877740 Pinion Yoke 1350 Series Forged U-Bolt style fits 1985 to 1992 FORD F250, F350 Super Duty 10.25 inch Sterling rear ends
FOR FASTER SERVICE, PLEASE ORDER ALL PARTS ONLINE
STATUS:  IN STOCK - FREE SHIPPING
YOUR COST:  $125.95
This item qualifies for FREE GROUND SHIPPING to the lower 48 states

9877740

  • Pinion Yoke for FORD Super Duty Rear End
    • Fits Ford F250, F350 Super Duty Truck with 10.25 inch FORD Sterling Rear
      • 1985, 1986, 1987, 1988, 1989, 1990, 1991, 1992
  • 31 Splines 1.343 spline diameter
  • U- Bolt style
  • FORGED Steel for extra strength
  • Comes with pinion nut and u-bolt set
  • 1350 Series - fits 1350 series universal joint 5-178X or 5-1350X ... see bottom of this page
    • E = Fits Universal joint 3.625 inches (3-5/8) wide cap to cap
    • D = Fits u-joint bearing cap diameter 1.187 inch (1-3/16)
    • Q = 1.265 inches through splined hole
    • S = 3.150 inches tall
    • R = 1.812 inches seal surface diameter
THIS Yoke is 3-1/8 inches TALL
IMPORTANT:   Late 1993, 1994, 1995, 1996, 1997, 1998 Ford 10.25 inch Sterling rear end pinion yokes could be 3.5 inches (3-1/2) tall.  Please check yours to be sure before ordering.
  • CLICK HERE if you need the 3-1/2 inch tall yoke part number 9870041 for 10.25 inch from 1993 to 1998

NOTES:

  • DOES NOT fit Ford Super duty with DANA rear end
  • NOT compatible with 1330 series driveshaft. 
    • Requires 1330 to 1350 combination u-joint to make connection. CLICK HERE
  • NOT compatible with 1410 series driveshaft
    • CLICK HERE for 1410 series Ford Sterling pinion yokes
image/jpeg
9877740 Pinion Yoke 1350 Series Forged U-Bolt style fits 1985 to 1992 FORD F250, F350 Super Duty 10.25 inch Sterling rear ends

9877740 Pinion Yoke 1350 Series Forged U-Bolt style fits 1985 to 1992 FORD F250, F350 Super Duty 10.25 inch Sterling rear ends

Enter your email address and we'll send you a message when this item is available

Please enter your email address in order to be notified when this item is available.
DennysDriveshaft.com - © Copyright 2021-Present

Website and Web Hosting by Online Media
Online Media - Buffalo's Web Hosting Company