DennysDriveshaft.com
Free Shipping on Orders Over $99.00

Product Search
Denny's Driveshaft builds custom steel and aluminum driveshafts for your high performance car, street rod, race car, van, pick up or 4x4 truck
 
One Piece 3.5 inch ALUMINUM DRIVESHAFT 1350 series fits 2005 to 2010 FORD MUSTANG GT with V8 DANA SPICER 10001766 FREE SHIPPING
Part Number:
10001766


UPC:
023913435943
Your Cost $779.99
Sorry, sold out
STATUS:  DISCONTINUED ITEM

DANA SPICER 10001766

One Piece ALUMINUM DRIVESHAFT

  • Fits FORD MUSTANG GT with V8 engine 2005, 2006, 2007, 2008, 2009 and 2010
  • 1350 Series for extra strength and reliability
  • 3.5 inch Diameter .125 inch wall thickness 6061-T6 aluminum tubing
  • 1336 mm (52.598 inches) Overall Length....face of transmission flange to face of rear end flange dimension
  • Direct BOLT IN right out of the box

One Piece 3.5 inch ALUMINUM DRIVESHAFT 1350 series fits 2005 to 2010 FORD MUSTANG GT with V8 DANA SPICER 10001766

FREE GROUND Shipping**

**Free Ground Shipping to lower 48 States ONLY...Alaska and Hawaii at reduced rates.


 

Spicer
One Piece 3.5 inch ALUMINUM DRIVESHAFT 1350 series fits 2005 to 2010 FORD MUSTANG GT with V8 DANA SPICER 10001766 FREE SHIPPING
One Piece ALUMINUM DRIVESHAFT fits 2005 t o 2010 FORD MUSTANG GT with V8 3.5 inch 1350 series DANA SPICER 10001766
FOR FASTER SERVICE, PLEASE ORDER ALL PARTS ONLINE
STATUS:  DISCONTINUED ITEM
YOUR COST:  $779.99
This item qualifies for FREE GROUND SHIPPING to the lower 48 states

>>>>> SPECIAL ORDER PART:  This part number is special ordered from the factory and shipped direct to you.  It is NOT Cancellable and NOT Returnable.  Please make your selection carefully! <<<<<

DANA SPICER 10001766

One Piece ALUMINUM DRIVESHAFT

Fits FORD MUSTANG GT with V8 engine 2005, 2006, 2007, 2008, 2009 and 2010

  • 1336 mm (52.598 inches) Overall Length....face of transmission flange to face of rear end flange dimension
  • Direct BOLT IN right out of the box
  • Designed for Increased Horsepower applications to deliver peak endurance and optimum strength
    • 3.5 inch Diameter .125 inch wall thickness 6061-T6 aluminum tubing
    • 1350 SERIES Dana Spicer 5-1350X Universal Joints...much stronger than the 1330 series versions available for Mustangs
    • Comes with 1350 series flange yoke to bolt to transmission
    • Comes with 1350 series flange yoke to bolt to OE Mustang rear end flange...NO adaptor required
    • Fully Assembled and Balanced
  • Spline and Slip design to allow for installation and suspension movement
  • Hard Plastic boot to keep grease in and water out to protect spline and slip from contaminants
  • Reduces noise, vibration and harshness in your Mustang driveline
  • Eliminates the need for a center support bearing
  • Lighter Weight than OE Driveshaft - Reduces overall weight and rotating mass
  • Delivers improved driving performance
  • Provides quicker accelleration and faster ET at the track
  • Built, assembled and balanced by Dana Spicer

One Piece 3.5 inch ALUMINUM DRIVESHAFT 1350 series fits 2005 to 2010 FORD MUSTANG GT with V8 DANA SPICER 10001766

One Piece 3.5 inch ALUMINUM DRIVESHAFT 1350 series fits 2005 to 2010 FORD MUSTANG GT with V8 DANA SPICER 10001766 FREE SHIPPING

One Piece ALUMINUM DRIVESHAFT fits 2005 t o 2010 FORD MUSTANG GT with V8 3.5 inch 1350 series DANA SPICER 10001766

Enter your email address and we'll send you a message when this item is available

Please enter your email address in order to be notified when this item is available.
DennysDriveshaft.com - © Copyright 2024-Present

Website and Web Hosting by Online Media
Online Media - Buffalo's Web Hosting Company