DennysDriveshaft.com

Product Search
Denny's Driveshaft builds custom steel and aluminum driveshafts for your high performance car, street rod, race car, van, pick up or 4x4 truck
 
X-1 Center Support with stock 1.181 bearing ID Aluminum Urethane Mount for 1958 to 1964 Chevy Car and 1960 to 1972 C-10 Truck must be used with spline and slip rear driveshaft only
Part #:
X-1
Your Cost $178.95 $139.95

Denny's part number X-1

Aluminum Urethane mounted center support bearing

Designed to replace OEM rubber mounted center bearing with round bracket on 2 inch diameter original equipment driveshafts

  • 1.181 Bearing ID is same as stock center support bearing 210527X and will fit original stub on OEM driveshaft
  • Must be used with spline and slip style rear driveshaft section. See the bottom of this page for details.
  • Fits Chevrolet Car
    • 1958, 1959, 1960, 1961, 1962, 1963, 1964
  • Fits Chevy C-10 1/2 Ton Truck
    • 1960, 1961, 1962, 1963, 1964, 1965, 1966, 1967, 1968, 1969, 1970, 1971, 1972

Super Strong aircraft aluminum housing will not bend or twist. 

  • Bearing is suspended in Urethane and will not pull out under load like the original rubber mount did when it distorted under load. 
  • This could be the cure that you have been looking for to end all your problems with center hanger bearing failure
  • Great for cars and trucks with hydraulic suspensions
  • Comes with Mounting Bolts and washers

X-1 Center Support with stock 1.181 bearing ID Aluminum Urethane Mount for 1958 to 1964 Chevy Car and 1960 to 1972 C-10 Truck must be used with spline and slip rear driveshaft only
Denny's part number X-1 Center Support Bearing Aluminum Urethane Mount for 1958 to 1964 Chevy Car and 1960 to 1972 C-10 Truck
FOR FASTER SERVICE, PLEASE ORDER ALL PARTS ONLINE
STATUS:  IN STOCK
YOUR COST:  $178.95 $139.95

Denny's part number X-1

Aluminum Urethane mounted center support bearing

Designed to replace OEM rubber mounted center bearing with round bracket on 2 inch diameter original equipment driveshafts

  • 1.181 Bearing ID is same as stock center support bearing 210527X and will fit original stub on OEM driveshaft
  • Must be used with spline and slip style rear driveshaft section. See the bottom of this page for details.
  • Fits Chevrolet Car
    • 1958, 1959, 1960, 1961, 1962, 1963, 1964
  • Fits Chevy C-10 1/2 Ton Truck
    • 1960, 1961, 1962, 1963, 1964, 1965, 1966, 1967, 1968, 1969, 1970, 1971, 1972

Super Strong aircraft aluminum housing will not bend or twist. 

  • Bearing is suspended in Urethane and will not pull out under load like the original rubber mount did when it distorted under load. 
  • This could be the cure that you have been looking for to end all your problems with center hanger bearing failure
  • Great for cars and trucks with hydraulic suspensions
  • Comes with Mounting Bolts and washers
X-1 Center Support with stock 1.181 bearing ID Aluminum Urethane Mount for 1958 to 1964 Chevy Car and 1960 to 1972 C-10 Truck must be used with spline and slip rear driveshaft only

Denny's part number X-1 Center Support Bearing Aluminum Urethane Mount for 1958 to 1964 Chevy Car and 1960 to 1972 C-10 Truck


DennysDriveshaft.com - © Copyright 2017-Present

Website and Web Hosting by Online Media
Online Media - Buffalo's Web Hosting Company