X-1 Center Support with stock 1.181 bearing ID Aluminum Urethane Mount for 1958 to 1964 Chevy Car and 1960 to 1972 C-10 Truck must be used with spline and slip rear driveshaft only

Part Number:
X-1

UPC:

Your Cost $125.95

STATUS: IN STOCK - FREE SHIPPING

Denny's part number X-1

Aluminum Urethane mounted center support bearing

Designed to replace OEM rubber mounted center bearing with round bracket on 2 inch diameter original equipment driveshafts

1.181 Bearing ID is same as stock center support bearing 210527X and will fit original stub on OEM driveshaft
Must be used with spline and slip style rear driveshaft section. See the bottom of this page for details.
Fits Chevrolet Car
- 1958, 1959, 1960, 1961, 1962, 1963, 1964
Fits Chevy C-10 1/2 Ton Truck
- 1960, 1961, 1962, 1963, 1964, 1965, 1966, 1967, 1968, 1969, 1970, 1971, 1972

Super Strong aircraft aluminum housing will not bend or twist.

Bearing is suspended in Urethane and will not pull out under load like the original rubber mount did when it distorted under load.
This could be the cure that you have been looking for to end all your problems with center hanger bearing failure
Great for cars and trucks with hydraulic suspensions
Comes with Mounting Bolts and washers

Denny's part number X-1 Center Support Bearing Aluminum Urethane Mount for 1958 to 1964 Chevy Car and 1960 to 1972 C-10 Truck

Click for Larger Photo

FOR FASTER SERVICE, PLEASE ORDER ALL PARTS ONLINE

STATUS: IN STOCK - FREE SHIPPING

YOUR COST: $125.95

Denny's part number X-1

Aluminum Urethane mounted center support bearing

Designed to replace OEM rubber mounted center bearing with round bracket on 2 inch diameter original equipment driveshafts

1.181 Bearing ID is same as stock center support bearing 210527X and will fit original stub on OEM driveshaft
Must be used with spline and slip style rear driveshaft section. See the bottom of this page for details.
Fits Chevrolet Car
- 1958, 1959, 1960, 1961, 1962, 1963, 1964
Fits Chevy C-10 1/2 Ton Truck
- 1960, 1961, 1962, 1963, 1964, 1965, 1966, 1967, 1968, 1969, 1970, 1971, 1972

Super Strong aircraft aluminum housing will not bend or twist.

Bearing is suspended in Urethane and will not pull out under load like the original rubber mount did when it distorted under load.
This could be the cure that you have been looking for to end all your problems with center hanger bearing failure
Great for cars and trucks with hydraulic suspensions
Comes with Mounting Bolts and washers

Denny's part number X-1 Center Support Bearing Aluminum Urethane Mount for 1958 to 1964 Chevy Car and 1960 to 1972 C-10 Truck

You May Also Need These Parts to Complete the Job

Part number: 1310SS-25864 Driveshaft REAR SECTION Spline & Slip Style for 58-64 Chevy and 55-72 Trucks Part#: 1310SS-25864 $295.95	2-4-1921 yoke 1958-1964 Chevrolet Car 60-72 C-10 Truck 1310 Series bolt on center driveshaft yoke Part#: 2-4-1921 $76.95
1958 to 1964 Chevrolet 55-72 Truck Bolt, Lock Washer and Flat Washer for OE Driveshaft Part#: 1474822 $5.78	Dana Spicer 5-153X Greaseable U-Joint for 58-64 Chevrolet Cars and 55-72 C10 trucks Part#: 5-153X $13.09
DANA SPICER 5-1310X NON Greaseable Universal Joint fits 58-64 Chevrolet Cars and 55-72 Light Trucks Part#: 5-1310X $19.66

Enter your email address and we'll send you a message when this item is available

Please enter your email address in order to be notified when this item is available.

[ X ]

Chevrolet > 1958 to 1964 CHEVY CAR - 1960 to 1972 C-10 TRUCK > CENTER BEARINGS, YOKE, STUB > STOCK Driveshaft 1.181 ID Brg with Air Ride

You May Also Need These Parts to Complete the Job

Enter your email address and we'll send you a message when this item is available