DennysDriveshaft.com
Free Shipping on Orders Over $99.00

Product Search
Denny's Driveshaft builds custom steel and aluminum driveshafts for your high performance car, street rod, race car, van, pick up or 4x4 truck
 
X-1574 Center Support with 1.574 bearing ID Aluminum Urethane Mount for 1958 to 1964 Chevy Car and 1960 to 1972 C-10 Truck for use with custom aftermarket driveshaft
Part Number:
X-1574


UPC:
Your Cost $237.25
Sorry, sold out
STATUS:  DISCONTINUED ITEM

Denny's part number X-1574

Aluminum Urethane mounted center support bearing

WILL NOT FIT STOCK DRIVESHAFT

Can be used on 3 inch diameter custom built 1350 series 2 piece driveshafts that require a 1.574 ID bearing

  • Ideal for building larger and stronger two piece driveshaft in 1310 or 1350 series
  • Bearing ID is 1.574 for use with custom built aftermarket driveshaft
  • Must be used with spline and slip style rear driveshaft section
  • Aluminum Mounting fits Chevrolet Car frame
    • 1958, 1959, 1960, 1961, 1962, 1963, 1964
  • Aluminum Mounting fits Chevy C-10 1/2 Ton Truck frame
    • 1960, 1961, 1962, 1963, 1964, 1965, 1966, 1967, 1968, 1969, 1970, 1971, 1972

Super Strong aircraft aluminum housing will not bend or twist. 

  • Bearing is suspended in Urethane and will not pull out under load like the original rubber mount did when it distorted under load. 
  • This could be the cure that you have been looking for to end all your problems with center hanger bearing failure
  • Great for cars and trucks with hydraulic suspensions
  • Comes with Mounting Bolts and washers

X-1574 Center Support with 1.574 bearing ID Aluminum Urethane Mount for 1958 to 1964 Chevy Car and 1960 to 1972 C-10 Truck for use with custom aftermarket driveshaft
Denny's part number X-1574 Center Support Bearing Aluminum Urethane Mount for 1958 to 1964 Chevy Car and 1960 to 1972 C-10 Truck
FOR FASTER SERVICE, PLEASE ORDER ALL PARTS ONLINE
STATUS:  DISCONTINUED ITEM
YOUR COST:  $237.25

Denny's part number X-1574

Aluminum Urethane mounted center support bearing

WILL NOT FIT STOCK DRIVESHAFT

Can be used on 3 inch diameter custom built 1350 series 2 piece driveshafts that require a 1.574 ID bearing

  • Ideal for building larger and stronger two piece driveshaft in 1310 or 1350 series
  • Bearing ID is 1.574 for use with custom built aftermarket driveshaft
  • Must be used with spline and slip style rear driveshaft section
  • Aluminum Mounting fits Chevrolet Car frame
    • 1958, 1959, 1960, 1961, 1962, 1963, 1964
  • Aluminum Mounting fits Chevy C-10 1/2 Ton Truck frame
    • 1960, 1961, 1962, 1963, 1964, 1965, 1966, 1967, 1968, 1969, 1970, 1971, 1972

Super Strong aircraft aluminum housing will not bend or twist. 

  • Bearing is suspended in Urethane and will not pull out under load like the original rubber mount did when it distorted under load. 
  • This could be the cure that you have been looking for to end all your problems with center hanger bearing failure
  • Great for cars and trucks with hydraulic suspensions
  • Comes with Mounting Bolts and washers
X-1574 Center Support with 1.574 bearing ID Aluminum Urethane Mount for 1958 to 1964 Chevy Car and 1960 to 1972 C-10 Truck for use with custom aftermarket driveshaft

Denny's part number X-1574 Center Support Bearing Aluminum Urethane Mount for 1958 to 1964 Chevy Car and 1960 to 1972 C-10 Truck

Enter your email address and we'll send you a message when this item is available

Please enter your email address in order to be notified when this item is available.
DennysDriveshaft.com - © Copyright 2024-Present

Website and Web Hosting by Online Media
Online Media - Buffalo's Web Hosting Company